How does a kicker motor bracket work?

The kicker motor mounts on a bracket on the transom, usually to the left side of the main outboard motor or transom mounted sailboat rudder, which allows the kicker motor to be locked in a stowed position out of the water, and then lowered into the water for use.

First and foremost, using a kicker motor helps you save on gas. Trolling with a kicker offers great gas to time ratio, which helps save on the gas you would have been using with your main outboard. Along with gas, they help prevent putting unwanted hours on your main outboard.

Secondly, how far outboard should water be? A boat rigger’s rule of thumb is that the motor can be raised one inch for each eight to 10 inches of distance between the transom and prop. As the prop moves further aft, it’s also likely to be in cleaner, “harder” water, and be more efficient.

Correspondingly, how do you install an outboard motor bracket?

Outboard Motor Bracket Instructions (Product Manual)

  1. Measure the distance between the top of the mounting clamp to the bottom of the cavitation plate. Subtract 2” from this length.
  2. Once you have determined the above length, mark this. distance on a stick.
  3. Position your outboard motor bracket, with the stick taped.
  4. With the outboard motor bracket positioned in the.

How do you mount a kicker motor bracket?

  1. Turn the main outboard motor or rudder as you would for a full left turn.
  2. Mount the kicker motor to the bracket.
  3. Remove the kicker motor from the bracket.
  4. Place the bracket on the transom to the left of the main outboard or rudder.

How do you hook up a fuel line to a kicker motor?

Seemingly the 3 methods are: Install a T fitting in the supply line from the fuel tank and branch off to the main motor and the kicker. Install a water/fuel separator filter (that has a minimum of 1 inlet and 2 outlets) in the supply line from the fuel tank. Install a ball valve in the supply line from the fuel tank.

Where do you mount a kicker motor?

Since the outboard tiller is usually on the port side of the motor, most kickers are mounted on the starboard-side of the transom to facilitate easier tiller steering and throttle control while slow-trolling or putting home.

What side does a kicker motor go on?

left

Can you put a kicker motor on a pontoon boat?

The Toon Kicker makes it possible to mount an auxiliary trolling motor on a pontoon boat. The Toon Kicker can be mounted to port or starboard of the main motor, and a slotted backing plate for the brace makes it possible to fit the unit most boats.

Do I need a kicker motor to troll?

If your main motor trolls slowly enough you don’t need a kicker. But kickers do make it easier to make small adjustments in speed and provide a back up if the main motor fails.

How do I know if I have a long or short shaft?

Measure from the bottom of your outboard’s engine compartment down to the bottom of the cavitation plate — the horizontal metal wing above the propeller. If the measurement lies between 19 and 21 inches, it’s a short shaft. If it’s about five inches longer than that, it’s a long shaft.

Why do boats have 2 motors?

Most boats are fitted with a powerful outboard (or multiple outboards) to accelerate to the fishing spot. After reaching the fishing spot, they switch to the smaller lower power engine for low noise levels. Trolling of fish needs low noise levels.

How do I slow my boat down for trolling?

Here are six ways to slow the pace, no matter what kind of boat you fish. Shut Down Your Boat’s Engine(s) Shifting Engines Out of Gear. Using Drift Socks and Trolling Bags. Benefits of an Auxiliary Outboard Engine. Using an Electric Motor. Outboard Engines with Troll Mode.

What is Mercury Pro Kicker?

The fastest power tilt in the industry drops a Mercury 9.9 – 15hp ProKicker FourStroke outboard into the water in just five seconds. Exclusive kicker-centering straps align and secure the outboard in full tilt-up position while you’re underway.

What size motor do I need for my boat?

The rule of thumb is based on weight alone, and says you should have between 40 and 25 pounds of weight for each horsepower. For example, a 5,000-pound boat could have an engine with between 125 and 200 horsepower.

What is an auxiliary motor?

The auxiliary motor is electrically connected to the auxiliary variable frequency drive. A gas turbine engine includes a compressor, a combustor adjacent the compressor, a turbine adjacent the combustor, a shaft, a motor, a primary variable frequency drive, an auxiliary variable frequency drive, and an auxiliary motor.