How long do furnace inducer Motors last?

Simply put, an inducer fan should start up when your thermostat calls for heat. It will do this anywhere from 30 seconds to one minute. It then stays running for as long as your system is heating the house and shuts off when your system cycles off.

The average furnace inducer motor cost is around $245, when the part is under warranty and you pay only the labor to have it installed. The replacement cost is $465 when the warranty has expired and you pay for the furnace inducer motor.

how much is a motor for a furnace? Motor type Standard blower motors operate at a single speed and cost around $450 to replace, including parts and labor. Variable-speed motors cost $600 and up to replace.

Likewise, what does an inducer motor do on a furnace?

A furnace draft inducer blower is a relatively new component of modern furnaces that became part of heating units after government-mandated efficiency standards were enacted. The draft inducer blower’s purpose is to move air and gases out of the furnace and up through the chimney.

How do you replace a furnace inducer blower?

How to Replace a Furnace Draft Inducer Blower

  1. Step 1 – Purchase the Part. Have a good look at the furnace draft inducer blower that exists inside your furnace.
  2. Step 2 – Turn off the Power.
  3. Step 3 -Remove the Draft Inducer Blower.
  4. Step 4 – Install the new Draft Inducer Blower.

What does a new furnace cost?

The national average cost of a standard efficiency natural gas furnace ranges from $2,150 to $5,900 with most homeowners paying around $3,100. The price may vary based on brand, complexity of install, and the efficiency of the new unit. Get free estimates from furnace replacement pros near you.

How long should a furnace last?

15 years

How do I clean my furnace?

How to Clean a Gas Furnace Turn off power/gas to the furnace. Turn off power to the furnace at the breaker box. Clean furnace surfaces. Wipe exterior surfaces with a damp rag. Remove the blower. Carefully clean the blower. Clean the pilot or hot surface igniter. Clean the flame sensor. Inspect the drive belt. Lubricate (but not too much).

How much does a furnace inspection cost?

Expect to spend anywhere from about $80 to $100 for a furnace tune-up, but more if repairs are also needed. Many companies offer service contracts or maintenance plans, which may reduce the cost of an annual visit from a pro and provide other benefits.

What is a furnace tune up?

During a tune-up, a technician will clean and adjust the parts and mechanisms inside your furnace. This will keep the furnace running efficiently throughout the season. Your tech will also perform a comprehensive inspection to catch potential problems before they escalate into a full-scale furnace breakdown.

Where is the inducer motor on a furnace?

A draft inducer is a fan that’s located inside of your furnace near the heat exchanger. When your furnace begins a heating cycle, the draft inducer is one of the first devices that turns on. In fact, the draft inducer starts up 30-60 seconds before the burners are lit and continues to run throughout each heating cycle.

How do you troubleshoot a furnace?

Furnace Troubleshooting Recap: Clean or replace air filter. Troubleshoot thermostat problems — replace batteries if necessary. Set thermostat to heat and at a higher temperature than the current room temperature. Check electrical panel for blown fuses or tripped breakers. Make power switch near furnace is flipped on.

Why is my furnace not getting gas?

Check Your Air Filters Often times the reason air does not get to your furnace’s igniter is because it is restricted. The main reason for this air restriction is usually traced back to dirty air filters. So check them if your gas furnace fails to ignite when you turn the system on.

How do you test a blower motor?

If the blower motor isn’t running you should: Use voltmeter or ohmmeter to check for a blown fuse. If you find one, replace it. Start car and see if blower motor works. If the circuits are in good repair but the blower motor keeps blowing fuses, replace the blower motor [source: You Fix Cars].

Can a furnace ignitor be cleaned?

A dirty ignitor will prevent your furnace from lighting. The ignitor takes a small amount of electricity and ignites the fuel to create the heat in your furnace. Repairing this item usually means replacement. Before you replace the ignitor, try cleaning it with a quick blast of air.

Why did my furnace stop working?

Furnace filters A clogged furnace filter can cause a furnace to shut off. Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up.