What guitars have a nitrocellulose finish?

Nitrocellulose lacquers have been around for almost a century; originally used for acoustic instruments, saxophones and even cars. This finish later became a popular choice for Fender and Gibson in the ’50s and ’60s, who used it almost exclusively for their electric guitars.

Guitar Finishes

  • Lacquer. Nitrocellulose-lacquers.
  • From the beginning, wood was the natural choice for most tools and useful objects. It was plentiful, easy to work and available in all useful sizes.
  • Lacquer.
  • Nitrocellulose Lacquers.
  • Acrylic Lacquers.
  • Polyurethane Lacquers.
  • Polyester Finishes.
  • Catalyzed Lacquer.

One may also ask, does Guitar Finish affect tone? DOES A GUITAR’S FINISH REALLY AFFECT THE OVERALL TONE? A: Traditional finishes, such as varnishes and nitrocellulose lacquer, take many years or even decades to fully cure, while catalyzed finishes, like urethane and polyester, can cure in a matter of days.

Similarly, it is asked, do Martin guitars have nitrocellulose finish?

All modern Martin’s have a nitrocellulose finish, shellac hasn’t been used since the early 1920’s. Not sure how Martin does it, but a flattening agent can be added to gloss lacquer to make it satin. martin uses a product called chem sheen , it is a satin finished lacquer.

What is the difference between acrylic and nitrocellulose lacquer?

Yes, acrylic does dry faster than nitrocellulose and I think it would be a good choice for a guitar finish. It also doesn’t yellow – a plus or a minus depending on your view of relics – and produces a less brittle, more flexible finish. It is more expensive than nitro though.

Can you use polyurethane on a guitar?

Poly finishes completely harden and solvents cannot break them down, Poly finishing is very resistant to cracks, dulling and scratching while also being durable. If you want the new shine finish to last a long time, as long as you have your guitar, then a Poly finish is what you want.

Can you relic a poly finish?

Kyri Senior Stratmaster. easiest way is to remove the poly, then refinish in nitro, play the snot out of the guitar, and let nature take it’s course. otherwise, try feathering in the chipped areas, it’ll smooth the hard line between the finish and the wood.

Does fender still use nitrocellulose?

Fender still uses nitrocellulose lacquer finishes on a select group of instruments (Road Worn™ and American Vintage series, various artist models).

How long should you wait between coats of lacquer?

How long should I leave between coats? Drying time is affected by temperature. As a rule of thumb for nitrocellulose lacquers, apply 3 coats over a 30 minute period, then leave to dry for about 6 hours, or overnight. Then apply a further 3 coats and repeat until you have built up sufficient lacquer or paint.

What clear coat is used on guitars?

Acrylic lacquer will be the go. If you want high gloss it will take a few coats depending on your prep work.. Wet it in with thinned down coats at the end it really helps.

Is my guitar Poly or nitro?

Just burn the guitar. If the fire has red flames and it smells spicy and aromatic then it is Nitro. Are the flames more orange-ish and bright and it smells chemical like you burn some plastic cups then it is Poly.

What is nitrocellulose finish?

It was composed of cellulose treated with nitric acid and a solvent. It is an exceptionally fast-drying solvent finish and a stronger version of the original shellacs and varnishes. Nitrocellulose lacquer can be applied in multiple coats, but the resulting finish is still thin and protective.

Can you brush on nitrocellulose lacquer?

brushing is not the best way to apply lacquer you will feel it grabing pretty quickly , there is a brushing lacquer but it isn’t great for guitars. If you mask the area the you don’t want over spray you will be better off than brushing.

How long does nitroglycerin take to cure?

Nitro if three or more coats they recommend 30 days to harden before doing anything .

How long does it take for lacquer to dry?

Lacquer dries in no more than half an hour, but it must cure completely between coats. Let the newly sprayed wood dry for about 48 hours, or as directed by the manufacturer. Then lightly smooth the surface with No. 000 steel wool, and clean it thoroughly with a tack cloth.